Passive faulttolerant control for vehicle active suspension system based on H2/H∞ approach
Li Ping Zhang^{1} , Dong Liang Gong^{2}
^{1, 2}College of Automobile and Traffic Engineering, Liaoning University of Technology, Jinzhou, P. R. China
^{1}Corresponding author
Journal of Vibroengineering, Vol. 20, Issue 4, 2018, p. 18281849.
https://doi.org/10.21595/jve.2017.18264
Received 20 February 2017; received in revised form 28 November 2017; accepted 12 December 2017; published 30 June 2018
JVE Conferences
In this paper, a robust passive faulttolerant control (RPFTC) strategy based on ${H}_{2}/{H}_{\infty}$ approach and an integral sliding mode passive fault tolerant control (ISMPFTC) strategy based on ${H}_{2}/{H}_{\infty}$ approach for vehicle active suspension are presented with considering model uncertainties, loss of actuator effectiveness and timedomain hard constraints of the suspension system. ${H}_{\infty}$ performance index less than $\gamma $ and ${H}_{2}$ performance index is minimized as the design objective, avoid choosing weighting coefficient. The halfcar model is taken as an example, the robust passive faulttolerant controller and the integral sliding mode passive fault tolerant control law is designed respectively. Three different fault modes are selected. And then compare and analyze the control effect of vertical acceleration of the vehicle body and pitch angular acceleration of passive suspension control, robust passive fault tolerant control and integral sliding mode passive fault tolerant control to verify the feasibility and effectiveness of passive fault tolerant control algorithm of active suspension. The studies we have performed indicated that the passive fault tolerant control strategy of the active suspension can improve the ride comfort of the suspension system.
 Actuator partial failure, timedomain hard constraints and model uncertainties are considered.
 Two passive faulttolerant control strategy based on H2/H∞ approach are proposed.
 The proposed two control strategies can improve the ride comfort of the vehicle.
Keywords: active suspension, H2/H∞ control, parameter uncertainties, actuator faults, RPFTC, ISMPFTC.
1. Introduction
A suspension system is a very important component of any vehicle. It flexibly connects the vehicle body and the axles, carries the vehicle body; transmits all vertical forces between body and road, including bears the forces between the tires and body, absorbs the shock from the road surface; protects the vehicle from unwanted vibrations and avoids excessive suspension stroke or related hard stop/impact. The suspension plays a key role in the riding comfort and handling stability [13]. The primary functions of a vehicle suspension system are to isolate a car body from road disturbances in order to provide good ride quality, to keep good road holding, to provide good handling and support the vehicle static weight [4, 5]. Suspensions generally fall into either of two groupsdependent suspensions and independent suspensions. Suspension systems can be divided into passive suspension, semiactive suspension, and active suspension, according to the different control modes used [1]. There are generally three fundamental elements for a typical vehicle suspension system, including springing, damping, and location of the wheel [6]. Active suspension system contains separate actuator that is able to provide external forces to both add and dissipate energy from the system. The task of the suspension spring is to carry the body mass and to isolate the body from road disturbances. The suspension damper contributes to both driving safety and quality. Its task is the damping of body and wheel oscillations. A nonbouncing wheel is a condition for transferring roadcontact forces [2].
However, conventional suspensions can achieve a tradeoff between ride comfort and road holding since their spring and damping coefficients cannot be adaptively tuned according to driving efforts and road conditions. They can achieve good ride comfort and road holding only under the designed conditions [7]. Active suspension systems have the best potential to deal with conflicting objectives placed on a suspension system a potential to deal with the tradeoff between the conflicting suspension performance measures. Because vehicle active suspension can significantly improve the ride comfort of passengers, meet the requirements of handling stability simultaneously. Over the past three decades, many researchers have devoted themselves to the theory and simulation studies on the control method of vehicle active suspension. Many advances have been made in active suspension and control theory nowadays.
The active suspension control problem can be considered as a disturbance attenuation problem with timedomain hard constraints [8, 9]. The mixed ${H}_{2}/{H}_{\infty}$ guaranteed cost control problem of state feedback control laws is considered in [10] for linear systems with normbounded parameter uncertainty. The ${H}_{\infty}$ state feedback control strategy with time domain hard constraints was proposed under nonstationary running [11]. [12] designed a linear, robust, guaranteedcost state feedback control with pole region constraints subject to active suspension system uncertainties. By the LMI (Linear Matrix Inequalities) method, a convex optimization problem is formulated to find the corresponding controller. A 3 DOF quarter car model is used in [13]. LQR based fuzzy controller; Fuzzy PID controller and Linear Quadratic Controller (LQR) are designed respectively to analyze and compare the performance characteristics of the active system with the uncontrolled system or passive suspension system. In [14], a robust model predictive control algorithm for polytopic uncertain systems with timevarying delays is presented for active suspension systems. However, most often, controllers are designed for the faultless suspension system so that the closed loop meets given performance specifications in studies of active suspension. Since not taking full account of the suspension system may exist malfunctions such as actuators, sensors or model parameters, which may lead to a degraded system performance (unsatisfactory performance) or even the loss of the system function (even instability) [15]. That is to say, once an actuator or a sensor fault occurs in a suspension system, the conventional controllers cannot achieve better performance in comparison with the reliable and faulttolerant controllers.
Fault tolerant control systems (FTCS) as control systems that possess the ability to accommodate system component failures automatically. They are capable of maintaining overall system stability and acceptable performance in the event of such failures. FTCS were also known as selfrepairing, reconfigurable, restructurable, or self designing control systems [1719]. Generally speaking, fault tolerant control can be classified into two types: active fault tolerant control (AFTC) and passive fault tolerant control (PFTC). AFTC reacts to the system component failures actively, by means of a fault detection and diagnosis (FDD) component that detects, isolates, and estimates the current faults, and reconfiguring online the controller, so that the stability and acceptable performance of the entire system can be maintained [18, 19]. Robust control is closely related to passive fault tolerant control systems (PFTCS). The controller is designed to be robust against disturbances and uncertainty during the design stage. That is, controllers are designed to be robust against a class of presumed fault. In other words, the starting point of the design is to reduce system dependency on the operation of a single component, even in the case of such failures and no correction, the system can still maintain some “acceptable” level of performance or degrade gracefully [17]. This enables the controller to counteract the effect of a fault without requiring reconfiguration or fault detection and isolation(FDI). Passive schemes operate independently of any fault information and basically exploit the robustness of the underlying controller. Such a controller is usually less complex, but in order to cope with ‘worst case’ fault effects, has a certain degree of conservatism [16, 18, 19]. However, its advantages are obvious: the parameters and structure of the controller are to be designed fixed; it neither needs to adjust the control law and control parameters online, nor needs fault detection, diagnosis and isolation; it is easy to realize and has the advantage of avoiding the time delay, which is very important [2022].
A passive faulttolerant ${H}_{\infty}$ controller is designed in [23] such that the resulting control system is reliable since it has the capability of guaranteeing asymptotic stability and ${H}_{\infty}$ performance, and simultaneously satisfying the constraint performance in the scenarios of actuator failures. In [24], a faulttolerant control approach is proposed to deal with the problem of fault accommodation for unknown actuator failures of active suspension systems, where an adaptive robust controller is designed to adapt and compensate the parameter uncertainties, external disturbances and uncertain nonlinearities generated by the system itself and actuator failures. In [25], the robust faulttolerant ${H}_{\infty}$ control problem of active suspension systems with finitefrequency constraint is investigated. Both the actuator faults and external disturbances are considered in the controller synthesis. Other performances such as suspension deflection and actuator saturation are also considered. In [26], an adaptive fault tolerant control problem for halfcar active suspension system subject to Markovian jumping actuator failures is considered. By employing adaptive backstepping technique, a new adaptive fault tolerant control scheme is proposed, which ensures the boundedness in probability of the considered systems.
Sliding mode based control schemes are a strong candidate for fault tolerant control because of their inherent robustness to matched uncertainties. Actuator faults can be effectively modeled as matched uncertainties and therefore sliding mode based control schemes have an inherent capability to directly deal with actuator faults [27]. In [28], a new robust strategy is presented which utilized the proportionalintegral sliding mode control scheme. In [29] a sliding mode control is designed for a full nonlinear vehicle active suspension system. Sensor faults effects on the behavior of the controlled system are analyzed and a fault tolerant control strategy to compensate for the sensor faults is proposed. [30] presents adaptive sliding mode fault tolerant control for magnetorheological (MR) suspension system considering the partial fault of MR dampers. In [31], an adaptive proportionalintegralderivative (PID) controller is proposed. Designing an adaptation scheme for the PID gains to accommodate actuator faults. A fault tolerant control approach based on a novel sliding mode method is proposed in [32] for a full vehicle suspension system aims at retaining system stability in the presence of model uncertainties, actuator faults, parameter variations.
This paper is based on the previous research results, consider that the vehicle active suspension system offline designed controller in the event of malfunctions in actuators and model uncertainties cannot achieve the desired control effect, and even controller appear failure make the suspension system loss of stability. In view of this, under the premise of fully taken into account the time domain hard constraints of the suspension system; for the halfcar active suspension system with actuator faults and model uncertainties, a robust passive fault tolerant control scheme based on ${H}_{2}/{H}_{\infty}$ approach and an integral sliding mode passive fault tolerant control scheme based on ${H}_{2}/{H}_{\infty}$ approach is designed respectively.
2. Halfcar model
Vehicle vibration models can be divided into quartercar model, halfcar model, fullcar model. The quartervehicle model was initially developed to explore active suspension capabilities and gave birth to the concepts of skyhook damping and fast load leveling, which are now being developed toward actual, largescale production applications. The quartercar model has been the bench model used in the study of control algorithm for intelligent suspension system. Although the model is very simple and is considering only vertical vibration motions of the sprung mass and the unsprung mass, it is very useful in initial development. By considering the vertical dynamics and taking into account the vehicle’s symmetry, a suspension can be reduced to the quartercar model. To account for the pitch motion or roll motion, a halfcar model is adopted by many researchers. The model is considering the vertical vibration and pitch motions of vehicle body, and the vertical motion of front and rear wheels. The halfcar model was represented to simulate ride characteristics of a simplified whole vehicle, which leads to significant improvement in ride and handling. The vehicle body of the fullcar model is assumed to be rigid and has seven degreeoffreedom in heave, pitch, and roll directions [7].
A four degreeoffreedom halfcar model is shown in Fig. 1. The model can simultaneously represent the passive suspension and active/semiactive according to the state of the actuator. If the actuator is neglected, the model is a passive suspension. The model is an active suspension if the actuator can generate active control forces, while the model is a semiactive suspension if the actuator can provide only damping forces. The model has been used extensively in the literature and captures many important characteristics of vertical and pitch motions.
Fig. 1. Model of halfcar active suspension system
The halfcar model is shown in Fig. 1. With the assumption of a small pitch angle $\theta $, $\mathrm{s}\mathrm{i}\mathrm{n}\theta \approx \theta $, we have the following approximate linear relationships:
The dynamic equations of this model can be written as:
where ${m}_{u1}$, ${m}_{u2}$ are the front and rear unsprung mass respectively; ${I}_{p}$ is pitch moment of inertia; $\theta $ represents the pitch angular; ${m}_{s}$ is the sprung mass; ${K}_{1}$ and ${K}_{2}$ are the stiffness coefficient of front and rear suspension respectively;${C}_{s1}$ and ${C}_{s2}$ are the damping coefficient of front and rear suspension respectively; $a$ and $b$ are the distance of front and rear axle to sprung mass center of gravity respectively; ${u}_{1}$ and ${u}_{2}$ are actuator control output force of the front and rear suspension respectively; ${x}_{u1}$ and ${x}_{u2}$ are the displacements of the front and rear unsprung mass respectively; ${x}_{g1}$ and ${x}_{g2}$ are the road profile inputs of the front and rear suspension system respectively.
Taking into account the time domain hard constraints on the suspension system [8, 9], it is necessary to keep suspension dynamic displacement in the usable range, so as to avoid bumping the limit blocks:
where ${S}_{\mathrm{m}\mathrm{a}\mathrm{x}}$ is the maximum suspension deflection.
Consider that the driving stability of the vehicle requirements, the dynamic tyre load doesn’t exceed the static tyre load in order to ensure the tire's grip capacity:
where ${m}_{s1}$, ${m}_{s2}$ are the static load mass of the front and rear suspension parts respectively.
The active control force provided for the active suspension system should be confined to a certain range prescribed by limited power of the actuator:
where ${F}_{\mathrm{m}\mathrm{a}\mathrm{x}}$ represents actuator output threshold.
Generally speaking, ${H}_{\infty}$ control strategy can solve the robust stability problem of a controlled target, and ${H}_{2}$ control strategy lets the controlled targets have a better dynamic performance. Combining on ${H}_{2}/{H}_{\infty}$ to build a hybrid control strategy, the problems of robust stability and optimal dynamic performance of a controlled target can be solved with better results. For a halfvehicle model, the riding comfort is related to the body vertical acceleration, pitching angular acceleration. The handling stability is related to the front and rear tyre dynamic loads. Based upon this consideration, and also considering how to reduce the complexity of a controller, a multiobjective optimization control strategy for an active suspension system is introduced. Choosing ${H}_{\infty}$ norm as the robust performance index of the time domain hard constraints, ${H}_{2}$ norm as the timedomain LQG performance index of perturbation action.
That is, the constrained output (${\mathbf{Z}}_{\mathbf{\infty}}$) and controlled output (${\mathbf{Z}}_{2}$) are defined as follows:
The selected state vector $\mathbf{X}={\left[{x}_{s1}{x}_{u1}{x}_{s2}{x}_{u2}{\dot{x}}_{s1}{\dot{x}}_{s2}{x}_{u1}{x}_{g1}{x}_{u2}{x}_{g2}{\dot{x}}_{u1}{\dot{x}}_{u2}\right]}^{T}$; the road surface vertical speed (${\dot{x}}_{g1},{\dot{x}}_{g2}$) are used as interference inputs, i.e. $\mathbf{W}=[{\dot{x}}_{g1},{\dot{x}}_{g2}{]}^{T}$. Then the governing equations ${\sigma}_{f}$ can be presented in the following statespace form:
where:
3. Modeling of faulty systems
3.1. Actuator fault model
The actuator common faults are outage, loss of effectiveness, and stuck. The actual control input ${\mathbf{u}}_{a}\left(t\right)$ which is able to impact the system is not the same as the designed control input $\mathbf{U}\left(t\right)$ designed in general. In this article, let ${\delta}_{1}$ and ${\delta}_{2}$ represent the percentage of efficiency loss of the front and rear actuator respectively. We only consider loss of effectiveness faults occur to the actuators. If losses of effectiveness faults occur to the actuators, the faulty actuators will fail to provide the desired control effects [20, 21]. That is, the faulty actuators can be formulated as:
where ${\delta}_{i}\in \left[01\right](i=1,2)$, then ${1\delta}_{i}\in \left[01\right]$. Define the actuator failure switch matrix as:
such as:
Define the failure factor ${m}_{i}=1{\delta}_{i}(i=1,2)$ in $\mathbf{M}$, so then, ${0\le m}_{li}\le {m}_{i}\le {m}_{ui}$, ${m}_{li}$ and ${m}_{ui}$ represent the known lower and upper bounds of ${m}_{i}$ respectively. If ${m}_{li}={m}_{ui}=0$, it covers to the outage case. If ${0\le m}_{li}<{m}_{i}<{m}_{ui}$ and ${m}_{i}\ne 1$, it corresponds to the partial failure case. And, faultfree (normal) case with ${m}_{li}={m}_{ui}=1$. In order to facilitate the analysis, the following matrix is introduced [24]:
where ${m}_{0i}=({m}_{li}+{m}_{ui})/2$, ${l}_{i}=({m}_{i}{m}_{0i})/{m}_{0i}$, ${j}_{i}=\left({m}_{ui}{m}_{li}\right)/\left({m}_{ui}+{m}_{li}\right)(i=1,2)$. The fault switch matrix can be expressed as:
3.2. Uncertainty model
Model uncertainties change the model parameters. In this paper, we will consider the following structure for the normbounded uncertainty:
where $\u2206\mathbf{A}$, $\u2206{\mathbf{B}}_{2}$ are real matrix functions representing timevarying parameter uncertainties. $\mathbf{H}$, ${\mathbf{E}}_{1}$, ${\mathbf{E}}_{2}$ are known constant matrices of appropriate dimensions which characterize how the uncertain parameters in $\mathbf{F}\left(t\right)$. $\mathbf{F}\left(t\right)\in {R}^{i\times j}$ is an unknown real timevarying matrix with Lebesgue measurable elements satisfying:
where $\mathbf{I}$ is an unit matrix of the appropriate dimension [10].
The stiffness and damping of active suspension change according to the sine function; variation range is both 20 %. Then in the light of Eq. (15), considering that the matrix $\mathbf{A}$, ${\mathbf{B}}_{2}$ contain the stiffness and damping parameters and as well as the dimension of them, meanwhile in accordance with the given variation range perturbation, we can know that $\mathbf{H}$ is 8×4 matrix, ${\mathbf{E}}_{1}$ is 4×8 matrix, ${\mathbf{E}}_{2}$ is 4×2 matrix.
3.3. The fault suspension model
Due to the active suspension system with consideration of both uncertainty and actuator failures, thus, the fault system ${\mathrm{\Omega}}_{f}$ can be written by:
4. Passive faulttolerant controller design
4.1. Robust passive faulttolerant controller design based on ${\mathit{H}}_{2}/{\mathit{H}}_{\mathit{\infty}}$ approach
The designed ${H}_{2}/{H}_{\infty}$ state feedback controller in the active suspension intact and troublefree condition is:
According to the faulty suspension system Eq. (17), the designed state feedback robust passive fault tolerant control law as follows:
such that for all admissible parameter uncertainties, the following design criteria are satisfied:
1) The resulting closedloop system is asymptotically stable.
2) If $\mathbf{W}\left(t\right)$ is viewed as a finite energy disturbance signal, the closedloop transfer function ${G}_{{Z}_{\infty W}}\left(s\right)$ from $\mathbf{W}\left(t\right)$ to ${\mathbf{Z}}_{\infty}\left(t\right)$ satisfies:
where ${\Vert {G}_{{Z}_{\infty W}}\left(s\right)\Vert}_{\infty}=\underset{W}{\mathrm{sup}}{\sigma}_{\mathrm{m}\mathrm{a}\mathrm{x}}\left\{{G}_{{Z}_{\infty W}}\left(jW\right)\right\}$, ${\sigma}_{\mathrm{m}\mathrm{a}\mathrm{x}}(\bullet )$ denotes the largest singular value, and $\gamma >0$ is a prespecified disturbance attenuation level;
3) If $\mathbf{W}\left(t\right)$ is viewed as a white noise signal with the unit power spectral density, an upper bound of the worst case ${H}_{2}$ performance index defined by:
where $\stackrel{}{J}\left({\mathbf{K}}_{f}\right)$ is a certain constant, $E\left\{\bullet \right\}$ denotes the expectation.
Substituting the control law Eq. (19) into fault suspension model Eq. (17), we obtain the available fault suspension state feedback closedloop system ${\mathrm{\Sigma}}_{f}$:
where ${\mathbf{A}}_{c}{=\mathbf{A}+\mathbf{B}}_{2}\mathbf{M}{\mathbf{K}}_{f}\text{,}$${\mathbf{E}}_{c}{={\mathbf{E}}_{1}+\mathbf{E}}_{2}\mathbf{M}{\mathbf{K}}_{f}\text{,}$${\mathbf{C}}_{1c}{={\mathbf{C}}_{1}+\mathbf{D}}_{12}\mathbf{M}{\mathbf{K}}_{f}\text{,}$${\mathbf{C}}_{2c}{={\mathbf{C}}_{2}+\mathbf{D}}_{22}\mathbf{M}{\mathbf{K}}_{f}\text{,}$${\stackrel{}{\mathbf{A}}}_{c}{=(\mathbf{A}+\mathbf{B}}_{2}\mathbf{M}{\mathbf{K}}_{f})+\mathbf{H}\mathbf{F}\left({{\mathbf{E}}_{1}+\mathbf{E}}_{2}\mathbf{M}{\mathbf{K}}_{f}\right)={\mathbf{A}}_{c}+\mathbf{H}\mathbf{F}{\mathbf{E}}_{c}$.
If ${\stackrel{}{\mathbf{A}}}_{c}$ is asymptotically stable, then the performance index $J\left({\mathbf{K}}_{f}\right)$ can be computed by:
where $\stackrel{~}{\mathbf{P}}={\stackrel{~}{\mathbf{P}}}^{T}\ge 0$ is the observability Gramian matrix obtained from the following Lyapunov equation:
Lemma 1 [23]: for any matrices $\mathbf{X}$ and $\mathbf{Y}$ with appropriate dimensions, for any $\eta >0$, we have:
Theorem 1 [10]: For a given constant $\gamma >0$ and the closedloop system ${\mathrm{\Sigma}}_{f}\text{,}$${\stackrel{}{\mathbf{A}}}_{c}$ is asymptotically stable and ${\Vert {G}_{{Z}_{\infty W}}\left(s\right)\Vert}_{\infty}<\gamma $ if and only if there exist two scalars $\alpha >0$ and $\beta >0$ such that the following matrix inequality:
has a symmetric positive definite solution $\mathbf{P}$; furthermore, if Eq. (26) has a symmetric positive definite solution $\mathbf{P}$, then for all admissible parameter uncertainties:
where $\stackrel{~}{\mathbf{P}}={\stackrel{~}{\mathbf{P}}}^{\mathbf{T}}\ge 0$ is a solution to lyapunov Eq. (24).
The matrix inequality Eq. (26) multiplied by ${\mathbf{P}}^{1}$ on both sides respectively such that:
${+\beta}^{1}{\mathbf{P}}^{1}{\mathbf{C}}_{1c}^{T}{\mathbf{C}}_{1c}{\mathbf{P}}^{1}+{\mathbf{P}}^{1}{\mathbf{C}}_{2c}^{T}{\mathbf{C}}_{2c}{\mathbf{P}}^{1}0.$
According to the Schur complement, the matrix inequality Eq. (28) is equivalent to Eq. (29):
Let ${\mathbf{Q}=\mathbf{P}}^{1}$, ${\mathbf{V}={\mathbf{K}}_{f}\mathbf{P}}^{1}$; substituting ${\mathbf{A}}_{c}$, ${\mathbf{E}}_{c}$, ${\mathbf{C}}_{1c}$, ${\mathbf{C}}_{2c}$ into the inequality Eq. (29) such that:
In this paper, we agree on that “*” represent symmetric transpose of the matrix; substituting the fault switch matrix Eq. (13) into the matrix inequality Eq. (30), then considering that the matrix inequality Eq. (14) and according to the lemma 1 such that:
$+\eta \left[\begin{array}{cccc}{\mathbf{B}}_{2}{\mathbf{M}}_{0}\mathbf{J}{\left({\mathbf{B}}_{2}{\mathbf{M}}_{0}\right)}^{T}& {\mathbf{B}}_{2}{\mathbf{M}}_{0}\mathbf{J}{\left({\mathbf{E}}_{2}{\mathbf{M}}_{0}\right)}^{T}& {\mathbf{B}}_{2}{\mathbf{M}}_{0}\mathbf{J}{\left({\mathbf{D}}_{12}{\mathbf{M}}_{0}\right)}^{T}& {\mathbf{B}}_{2}{\mathbf{M}}_{0}\mathbf{J}{\left({\mathbf{D}}_{22}{\mathbf{M}}_{0}\right)}^{T}\\ {\mathbf{E}}_{2}{\mathbf{M}}_{0}\mathbf{J}{\left({\mathbf{B}}_{2}{\mathbf{M}}_{0}\right)}^{T}& {\mathbf{E}}_{2}{\mathbf{M}}_{0}\mathbf{J}{\left({\mathbf{E}}_{2}{\mathbf{M}}_{0}\right)}^{T}& {\mathbf{E}}_{2}{\mathbf{M}}_{0}\mathbf{J}{\left({\mathbf{D}}_{12}{\mathbf{M}}_{0}\right)}^{T}& {\mathbf{E}}_{2}{\mathbf{M}}_{0}\mathbf{J}{\left({\mathbf{D}}_{22}{\mathbf{M}}_{0}\right)}^{T}\\ {\mathbf{D}}_{12}{\mathbf{M}}_{0}\mathbf{J}{\left({\mathbf{B}}_{2}{\mathbf{M}}_{0}\right)}^{T}& {\mathbf{D}}_{12}{\mathbf{M}}_{0}\mathbf{J}{\left({\mathbf{E}}_{2}{\mathbf{M}}_{0}\right)}^{T}& {\mathbf{D}}_{12}{\mathbf{M}}_{0}\mathbf{J}{\left({\mathbf{D}}_{12}{\mathbf{M}}_{0}\right)}^{T}& {\mathbf{D}}_{12}{\mathbf{M}}_{0}\mathbf{J}{\left({\mathbf{D}}_{22}{\mathbf{M}}_{0}\right)}^{T}\\ {\mathbf{D}}_{22}{\mathbf{M}}_{0}\mathbf{J}{\left({\mathbf{B}}_{2}{\mathbf{M}}_{0}\right)}^{T}& {\mathbf{D}}_{22}{\mathbf{M}}_{0}\mathbf{J}{\left({\mathbf{E}}_{2}{\mathbf{M}}_{0}\right)}^{T}& {\mathbf{D}}_{22}{\mathbf{M}}_{0}\mathbf{J}{\left({\mathbf{D}}_{12}{\mathbf{M}}_{0}\right)}^{T}& {\mathbf{D}}_{22}{\mathbf{M}}_{0}\mathbf{J}{\left({\mathbf{D}}_{22}{\mathbf{M}}_{0}\right)}^{T}\end{array}\right]$
${+{\eta}^{1}\left[{\mathbf{V}}^{T}{\mathbf{J}}^{1/2}\mathbf{}\mathbf{}\mathbf{}\mathbf{}000\right]}^{T}\left[{\mathbf{J}}^{1/2}\mathbf{V}000\right]0.$
In the light of the Schur complement such that:
where:
Considering that the fault suspension system Eq. (17) and a given $\gamma >0$, if the following optimization problem:
$\left(\text{ii}\right)\left[\begin{array}{c}N{\mathbf{B}}_{1}^{T}\\ {\mathbf{B}}_{1}Q\end{array}\right]0,$
by the solver $\mathrm{m}\mathrm{i}\mathrm{n}\mathrm{c}\mathrm{x}$ of the $LMI$ toolbox of the MATLAB has a solution ${\alpha}^{*}$, ${\beta}^{*}$, ${\eta}^{*}$, ${\mathbf{Q}}^{*}$, ${\mathbf{V}}^{*}$, ${\mathbf{N}}^{*}$, then the robust passive fault tolerant controller of the fault suspension loopsystem based on ${H}_{2}/{H}_{\infty}$ approach is:
4.2. Integral sliding mode faulttolerant controller design based on ${\mathit{H}}_{2}/{\mathit{H}}_{\mathit{\infty}}$ approach
According to Eq. (17), the fault system ${\mathrm{\Omega}}_{f}$ can be also written by:
where $\mathbf{\delta}=\mathrm{d}\mathrm{i}\mathrm{a}\mathrm{g}\left({\delta}_{1}{\delta}_{2}\right)$; let $\mathbf{\xi}=\mathbf{}\mathbf{\delta}\mathbf{U}$, ${\mathbf{f}}_{d}=\left[{\mathbf{B}}_{1}\mathbf{}\mathbf{H}{\mathbf{E}}_{1}\right]\left[\begin{array}{c}W\\ \mathrm{sin}t\end{array}\right]$, then Eq. (35) can be written as:
the actuator faults $\mathbf{\xi}$ can be effectively modelled as matched uncertainties.
Assumption 1. The function ${\mathbf{f}}_{d}$ represents unmatched uncertainty i.e. it does not lie within the range space of matrix ${\mathbf{B}}_{2}$, but is assumed to be bounded with known upper bound.
The nominal linear system associated with Eq. (36) can be written as:
where ${\mathbf{U}}_{0}$ is a nominal control law which can be designed by any suitable state feedback paradigm to achieve desired nominal performance. Since it is assumed that the pair $(\mathbf{A},{\mathbf{B}}_{2})$ is controllable, then there exists a state feedback controller of the form:
where $\mathbf{K}$ is a state feedback gain to be designed. The matrix $\mathbf{K}$ can be designed using any state feedback design approach. Here $\mathbf{K}$ is the designed ${H}_{2}/{H}_{\infty}$ state feedback gain.
Define the control law $\mathbf{U}$ of the form:
where ${\mathbf{U}}_{0}$ is the nominal controller and ${\mathbf{U}}_{n}$ is a nonlinear injection to induce a sliding mode. Then use Eq. (39), Eq. (36) can be written as:
where ${\mathbf{U}}_{n}$ is chosen to reject the disturbance term $\mathbf{\xi}$ while in the sliding mode. Here the switching function is defined as:
where $\mathbf{G}$ is design freedom and $\mathbf{z}$ is to be specified. Since the matrix ${\mathbf{B}}_{2}$ is of full rank, the switching matrix $\mathbf{G}$ can be chosen so that the matrix $\mathbf{G}{\mathbf{B}}_{2}$ is nonsingular i.e. $\mathit{det}\left(\mathbf{G}{\mathbf{B}}_{2}\right)\ne 0$. During sliding $\dot{\mathrm{\Phi}}=\mathrm{\Phi}=0$ and therefore:
During sliding it is expected that ${\mathbf{G}{\mathbf{B}}_{2}\mathbf{U}}_{neq}=\mathbf{}\mathbf{G}{\mathbf{B}}_{2}\mathbf{\xi}\mathbf{G}{\mathbf{f}}_{d}$, i.e.:
then selecting:
Substituting the value of equivalent control ${\mathbf{U}}_{neq}$ from Eq. (43) into Eq. (40) and simplifying, the expression for the integral sliding mode dynamics can be written as:
Let $\mathrm{\varnothing}=\mathbf{I}{\mathbf{B}}_{2}{\left(\mathbf{G}{\mathbf{B}}_{2}\right)}^{1}\mathbf{G}$, from Eq. (45) it is clear that the effect of the matched uncertainty has been completely rejected while in the sliding mode.
4.2.1. Integral switching surface
Using Eqs. (41, 44), an integral switching function:
The sliding mode will exist from time $t=0$ and the system will be robust throughout the entire closedloop system response against matched uncertainties. it is clear that in the case of only matched uncertainty, then any choice of $\mathbf{G}$ which ensures $\mathbf{G}{\mathbf{B}}_{2}$ is invertible is sufficient for the Integral sliding mode design, for unmatched uncertainty, a specific choice of $\mathbf{G}$ is needed. Here it will be argued that:
is an appropriate choice. Moreover, $\mathbf{G}{\mathbf{B}}_{2}=\mathbf{I}$.
This choice of $\mathbf{G}$ ensures that the square matrix $\mathbf{G}{\mathbf{B}}_{2}$ is nonsingular. The $\mathrm{\varnothing}$ becomes:
Notice that the projection operator $\mathrm{\varnothing}$ in Eq. (48) is symmetric and idempotent i.e. ${\mathrm{\varnothing}}^{2}=\mathrm{\varnothing}$. The properties of symmetry and idempotency imply that $\Vert \mathrm{\varnothing}\Vert =\text{1}$ which means that the effect of ${\mathbf{f}}_{d}$ is not amplified since $\Vert \mathrm{\varnothing}{\mathbf{f}}_{d}\Vert \le \Vert {\mathbf{f}}_{d}\Vert $.
4.2.2. Integral sliding mode control laws
An integral sliding mode controller will now be designed based on the nominal system in Eq. (37). The control law has a structure given by Eq. (39). ${\mathbf{U}}_{0}$ is the linear part of the controller, and ${\mathbf{U}}_{n}$ is the discontinuous part to enforce a sliding mode along the sliding surface in Eq. (46). One choice of $\mathbf{U}$ is:
where the value of the small positive scalar $\phi $ is chosen to eliminate chattering; $\rho $ is the modulation gain to enforce the sliding mode whose precise value is given later.
4.2.3. The reachability condition
To justify that the controller designed in Eq. (49) satisfies the $\mu $reachability condition, which is a sufficient condition to ensure the existence of an ideal sliding motion, it can be shown from Eq. (36) and Eq. (38) that:
then substituting from Eq. (50), and after some simplification:
$\mathbf{}\mathbf{}\mathbf{}\mathbf{}\mathbf{}\mathbf{}\mathbf{}\mathbf{}\mathbf{}\mathbf{}\mathbf{}\mathbf{}\mathbf{}=\rho \frac{\mathrm{\Phi}}{\Vert \mathrm{\Phi}\Vert +\phi}+\mathbf{G}{\mathbf{B}}_{2}\left(\mathbf{I}\right)\mathbf{\xi}+\mathbf{G}{\mathbf{f}}_{d}.$
Then:
In order to enforce a sliding mode the value of the modulation gain $\rho $ should be greater than any disturbance or uncertainty in the system, and therefore for any choice of $\rho $ which satisfies:
where $\mu $ is some positive scalar, the $\mu $reachability condition:
is satisfied.
5. Illustrative examples
In the following work, let PSC represents passive suspension control, which is represented by a black solid line of the figure; RPFTC represents robust passive fault tolerant control based on ${H}_{2}/{H}_{\infty}$ approach, which is represented by a red solid line of the figure; ISMPFTC represents integral sliding mode passive fault tolerant control based on ${H}_{2}/{H}_{\infty}$ approach, which is represented by a blue solid line of the figure. In this section, the simulation results of passive fault tolerant control of a halfcar model with actuator faults and model uncertainties are studied. All design parameters of the halfcar model in Fig. 1 are listed in Table 1. The design parameters are derived from reference [7]. Road interference inputs to use filter white noise and bump response respectively. As to response of excitation of random road surface, in simulation, consider three cases, which are Case one, Case two, Case three; where Case one represents active suspension in good condition；Case two represents the percentage of disturbance of active suspension system parameters is –10 %; when $t=$2.5 s, the percentage of efficiency loss of the front and rear actuator all is 0.4; Case three represents the percentage of disturbance of active suspension system parameters is 10 %; when $t=$2.5 s, the percentage of efficiency loss of the front and rear actuator all is 0.8. Concerning bump response, in simulation, consider three cases too, which are Case one, Case two, Case three; but in each case, consider three different vehicle speeds, which are $v=$20 km/h, $v=$ 25 km/h, $v=$30 km/h; where Case one represents active suspension in good condition; the vehicle forwards velocity is 20 km/h, 25 km/h, 30 km/h respectively; Case two represents the percentage of disturbance of active suspension system parameters is –10 %; the vehicle for velocity is 20 km/h, 25 km/h, 30 km/h respectively; when $t=$ 1 s, the percentage of efficiency loss of the front and rear actuator all is 0.4; Case three represents the percentage of disturbance of active suspension system parameters is 10 %; the vehicle speed is 20 km/h, 25 km/h, 30 km/h respectively; when $t=$ 1 s, the percentage of efficiency loss of the front and rear actuator all is 0.8. The performances of vehicle suspension with passive suspension control, robust passive fault tolerant control based on ${H}_{2}/{H}_{\infty}$ approach, integral sliding mode passive fault tolerant control based on ${H}_{2}/{H}_{\infty}$ approach are compared in the time domain.
The vehicle is assumed to run linearly and the road condition for rear wheel is same as the front wheel, but with a time delay of $(a+b)/v$. Using filtered white noise as the road inputs, the road input equations for the front and rear wheels are:
where ${f}_{0}$ is low cutoff frequency, ${f}_{0}=$ 0.01 m^{1}; ${G}_{0}$ is road roughness coefficient, ${G}_{0}=$5×10^{6} m^{3}; $v=$20 m/s; ${w}_{i}\left(t\right)$$$are white noise with zero mean and power spectral density of 1.
Consider the case of an isolated bump in a road surface, the bump road profile is described as follows:
where ${A}_{0}$ and $L$ are the height and the length of the bump. Assume ${A}_{0}=$ 0.08 m, $L=$ 5 m, the vehicle forwards velocity is 20 km/h, 25 km/h, 30 km/h respectively.
The matrix ${\mathbf{M}}_{0}$, $\mathbf{J}$ introduced in actuator fault model is ${\mathbf{M}}_{0}=0.5\bullet eye\left(2\right)$, $\mathbf{J}=eye\left(2\right)$, respectively. Constant matrices $\mathbf{H}$, ${\mathbf{E}}_{1}$, ${\mathbf{E}}_{2}$ of appropriate dimensions in uncertainty model is:
The obtained robust passive fault tolerant control law of the faulty suspension system based on ${H}_{2}/{H}_{\infty}$ approach is:
As to integral sliding mode passive fault tolerant control, $\rho $ is a fixed scalar and the value is 150; the value of the small positive scalar $\phi $ is chosen as $\phi =$ 0.4, to eliminate chattering.
Table 1. The vehicle system parameters for the halfcar model
Description

Variable

Units

Value

Sprung mass

${m}_{s}$

kg

690

Pitch moment of inertia

${I}_{p}$

kg∙m

1222

Front tire stiffness

${K}_{t1}$

N/m

200000

Rear tire stiffness

${K}_{t2}$

N/m

200000

Front suspension stiffness

${K}_{1}$

N/m

18000

Rear suspension stiffness

${K}_{2}$

N/m

22000

Front unsprung mass

${m}_{u1}$

kg

40

Rear unsprung mass

${m}_{u2}$

kg

45

Front Sprung damping coefficient

${C}_{s1}$

N∙s/m

1000

Front Sprung damping coefficient

${C}_{s2}$

N∙s/m

1000

Actuator output threshold

${F}_{\mathrm{m}\mathrm{a}\mathrm{x}}$

N

1500

The maximum suspension working space

${S}_{\mathrm{m}\mathrm{a}\mathrm{x}}$

m

0.08

Distance of front axle to sprung mass c.g.

$a$

m

1.3

Distance of rear axle to sprung mass c.g.

$b$

m

1.5

5.1. Simulation results
5.1.1. Response of excitation of random road surface
Case one: active suspension in good condition, the simulation results are shown in Figs. 23.
As for response to excitation of random road surface, in the first case, as is reflected in line charts 23 that the optimization effect are the integral sliding mode passive fault tolerant control based on ${H}_{2}/{H}_{\infty}$ approach is better than the robust passive fault tolerant control based on ${H}_{2}/{H}_{\infty}$ approach, and both of which are better than the passive suspension control.
Fig. 2. Timedomain analysis of vertical acceleration of vehicle body
Case two: The percentage of disturbance of active suspension system parameters is –10 %; when $t=$ 2.5 s, the percentage of efficiency loss of the front and rear actuator all is 0.4, the simulation results are shown in the line charts 45.
Fig. 3. Timedomain analysis of pitch acceleration
Fig. 4. Timedomain analysis of vertical acceleration of vehicle body
Fig. 5. Timedomain analysis of pitch acceleration
In Case two, when $t<$ 2.5 s, it can be seen from the line charts 45 that the control effect of the integral sliding mode passive fault tolerant control based on ${H}_{2}/{H}_{\infty}$ approach is the best, the robust passive fault tolerant control based on ${H}_{2}/{H}_{\infty}$ approach is the second best, the fault passive suspension control is the worst; when $t>$ 2.5 s, the order of the best optimization effects keeps the same.
Case three: The percentage of disturbance of active suspension system parameters is 10 %; when $t=$ 2.5 s, the percentage of efficiency loss of the front and rear actuator all is 0.8, the simulation results are shown in the line charts 67.
In Case three, when $t<$ 2.5 s, the line charts 67 illustrate that the optimization effect are the integral sliding mode passive fault tolerant control based on ${H}_{2}/{H}_{\infty}$ approach is better than the robust passive fault tolerant control based on ${H}_{2}/{H}_{\infty}$ approach, and both of which are better than the passive suspension control. When $t>$ 2.5 s, the control effect of the integral sliding mode passive fault tolerant control based on ${H}_{2}/{H}_{\infty}$ approach and the robust passive fault tolerant control based on ${H}_{2}/{H}_{\infty}$ approach is very close, but both of which are still slightly better than the passive suspension control.
Fig. 6. Timedomain analysis of vertical acceleration of vehicle body
Fig. 7. Timedomain analysis of pitch acceleration
5.1.2. Bump response
Case one: Active suspension in good condition; the vehicle forwards velocity is 20 km/h, 25 km/h, 30 km/h respectively; the simulation results are shown in Figs. 810.
Case two: The percentage of disturbance of active suspension system parameters is –10 %; the vehicle forwards velocity is 20 km/h, 25 km/h, 30 km/h respectively; when $t=$ 1 s, the percentage of efficiency loss of the front and rear actuator all is 0.4, the simulation results are shown in Figs. 1113.
Case three: The percentage of disturbance of active suspension system parameters is 10 %; the vehicle forwards velocity is 20 km/h, 25 km/h, 30 km/h respectively; when $t=$ 1 s, the percentage of efficiency loss of the front and rear actuator all is 0.8, the simulation results are shown in Figs. 1416.
Fig. 8. The bump responses from body vertical acceleration, pitch angular acceleration ($v=$20 km/h)
Fig. 9. The bump responses from body vertical acceleration, pitch angular acceleration ($v=$25 km/h)
Fig. 10. The bump responses from body vertical acceleration, pitch angular acceleration ($v=$30 km/h)
Fig. 11. The bump responses from body vertical acceleration, pitch angular acceleration ($v=$ 20 km/h)
Fig. 12. The bump responses from body vertical acceleration, pitch angular acceleration ($v=$ 25 km/h)
Fig. 13. The bump responses from body vertical acceleration, pitch angular acceleration ($v=$ 30 km/h)
Fig. 14. The bump responses from body vertical acceleration, pitch angular acceleration ($v=$ 20 km/h)
Fig. 15. The bump responses from body vertical acceleration, pitch angular acceleration ($v=$25 km/h)
Fig. 16. The bump responses from body vertical acceleration, pitch angular acceleration ($v=$ 30 km/h)
Concerning bump response, in the first case, active suspension in good condition, the vehicle forwards velocity is 20 km/h, it can be seen from the line chart 8 that the optimization effect of the integral sliding mode passive fault tolerant control (ISMPFTC) based on ${H}_{2}/{H}_{\mathrm{\infty}}$ approach is better than robust passive fault tolerant control (RPFTC) based on ${H}_{2}/{H}_{\mathrm{\infty}}$ approach, and both of which are better than the passive suspension control. When the vehicle for velocity is 25 km/h, from Fig. 9, one can find that the order for optimization effects is all same as those shown in Fig. 8, which are that the control effect of the integral sliding mode passive fault tolerant control based on ${H}_{2}/{H}_{\mathrm{\infty}}$ approach is the best, the robust passive fault tolerant control based on ${H}_{2}/{H}_{\mathrm{\infty}}$ approach is the second best, the passive suspension control is the worst. As is displayed Fig. 10 that this is also true when the vehicle speed is 30 km/h.
In Case two, the percentage of disturbance of active suspension system parameters is 10 %. When the vehicle forwards velocity is 20 km/h, $t<$ 1 s, the front and rear actuators are fault free, as is revealed line chart 11 that the control effect of the integral sliding mode passive fault tolerant control (ISMPFTC) based on ${H}_{2}/{H}_{\mathrm{\infty}}$ approach is better than robust passive fault tolerant control (RPFTC) based on ${H}_{2}/{H}_{\mathrm{\infty}}$ approach, and both of which are better than the passive suspension control. When $t\ge $ 1 s, the percentage of efficiency loss of the front and rear actuator all is 0.4, from Fig. 11, it can be concluded that the order of the best optimization effects keeps the same. When the vehicle for velocity is 25 km/h, $t<$ 1 s, the front and rear actuators are troublefree, as shown in the line chart 12 that the order for optimization effects is all same as those shown in Fig. 11. When $t\ge $ 1 s, the percentage of efficiency loss of the front and rear actuator all is 0.4, from Fig. 12, it can be seen that the order of the best optimization effects keeps the same, which are that the control effect of the integral sliding mode passive fault tolerant control based on ${H}_{2}/{H}_{\mathrm{\infty}}$ approach is the best, the robust passive fault tolerant control based on ${H}_{2}/{H}_{\mathrm{\infty}}$ approach is the second best, the passive suspension control is the worst. When the vehicle speed is 30 km/h, $t<$ 1 s, the front and rear actuators in good condition, the line chart 13 illustrates that the order of the best optimization effects is all same as those shown in Fig 12. When $t\ge $ 1 s, the percentage of efficiency loss of the front and rear actuator all is 0.4, as shown in the line chart 13 that the order of the best optimization effects keeps the same, which are that the optimization effect of the integral sliding mode passive fault tolerant control (ISMPFTC) based on ${H}_{2}/{H}_{\mathrm{\infty}}$ approach is better than robust passive fault tolerant control (RPFTC) based on ${H}_{2}/{H}_{\mathrm{\infty}}$ approach, and both of which are better than the passive suspension control.
In Case three, the percentage of disturbance of active suspension system parameters is 10 %. When the vehicle forwards velocity is 20 km/h, $t<$ 1 s, the front and rear actuators are fault free, as is displayed line chart 14 that the control effect of the integral sliding mode passive fault tolerant control based on ${H}_{2}/{H}_{\mathrm{\infty}}$ approach is the best, the robust passive fault tolerant control based on ${H}_{2}/{H}_{\mathrm{\infty}}$ approach is the second best, the passive suspension control is the worst. When $t\ge $ 1 s, the percentage of efficiency loss of the front and rear actuator all is 0.8, from Fig. 14, it can be seen that although the control effect of the integral sliding mode passive fault tolerant control based on ${H}_{2}/{H}_{\mathrm{\infty}}$ approach and the robust passive fault tolerant control based on ${H}_{2}/{H}_{\mathrm{\infty}}$ approach is very close, still slightly better than the passive suspension control. When the vehicle for velocity is 25 km/h, $t<$ 1 s, the front and rear actuators are troublefree, as is reflected in line chart 15 that the order of optimization effects are all same as those shown in Fig. 14. When $t\ge $ 1 s, the percentage of efficiency loss of the front and rear actuator all is 0.8, from Fig. 15, as is revealed that the control effect of the integral sliding mode passive fault tolerant control based on ${H}_{2}/{H}_{\mathrm{\infty}}$ approach and the robust passive fault tolerant control based on ${H}_{2}/{H}_{\mathrm{\infty}}$ approach is very close, but still slightly better than the passive suspension control. When the vehicle speed is 30 km/h, $t<$ 1 s, the front and rear actuators in good condition, as shown in the line chart 16 that the order of the best optimization effects keeps the same. When $t\ge $ 1 s, the percentage of efficiency loss of the front and rear actuator all is 0.8, the line chart 16 illustrates that the control effect of the integral sliding mode passive fault tolerant control based on ${H}_{2}/{H}_{\mathrm{\infty}}$ approach and the robust passive fault tolerant control based on ${H}_{2}/{H}_{\mathrm{\infty}}$ approach is very close, but both of which are still slightly better than the passive suspension control.
Table 2. RMS values of the performance indices for three failure modes
RMS

Case one


Parameter

${\ddot{x}}_{s}$

$\ddot{\theta}$

${\ddot{x}}_{s}$

$\ddot{\theta}$

${\ddot{x}}_{s}$

$\ddot{\theta}$

${\ddot{x}}_{s}$

$\ddot{\theta}$

PSC

0.4852

0.1931

1.2473

0.6163

1.3466

0.7614

1.3668

0.8321

RPFTC

0.3005

0.1195

0.6735

0.4106

0.7464

0.5201

0.7939

0.5907

ISMPFTC

0.2008

0.0797

0.4243

0.2633

0.4762

0.3163

0.5145

0.3568

Road type

Random road

$v=$ 20 km/h

$v=$ 25 km/h

$v=$30 km/h


Bump road


RMS

Case two


Parameter

${\ddot{x}}_{s}$

$\ddot{\theta}$

${\ddot{x}}_{s}$

$\ddot{\theta}$

${\ddot{x}}_{s}$

$\ddot{\theta}$

${\ddot{x}}_{s}$

$\ddot{\theta}$

PSC

0.5074

0.2063

1.3642

0.6604

1.4435

0.7833

1.4352

0.8300

RPFTC

0.3338

0.1240

0.7754

0.4605

0.8366

0.5688

0.8682

0.6234

ISMPFTC

0.2201

0.0876

0.5099

0.3241

0.5641

0.3883

0.6006

0.4252

Road type

Random road

$v=$ 20 km/h

$v=$ 25 km/h

$v=$30 km/h


Bump road


RMS

Case three


Parameter

${\ddot{x}}_{s}$

$\ddot{\theta}$

${\ddot{x}}_{s}$

$\ddot{\theta}$

${\ddot{x}}_{s}$

$\ddot{\theta}$

${\ddot{x}}_{s}$

$\ddot{\theta}$

PSC

0.4549

0.1855

1.1114

0.5625

1.2049

0.7192

1.2016

0.7798

RPFTC

0.3607

0.1267

0.7552

0.4490

0.8423

0.5876

0.8836

0.6509

ISMPFTC

0.2923

0.1051

0.5935

0.3745

0.6610

0.4876

0.7055

0.5390

Road type

Random road

$v=$ 20 km/h

$v=$ 25 km/h

$v=$30 km/h


Bump road

RMS values of the performance indices of the halfcar model with three failure modes are listed in Table 2 for quantifying and comparing the effects of these three control methods in different situations. It can be reached from Figs. 816 and Table 2 that at different vehicle speeds and failure modes, the optimization effect of the integral sliding mode passive fault tolerant control (ISMPFTC) based on ${H}_{2}/{H}_{\mathrm{\infty}}$ approach is better than robust passive fault tolerant control (RPFTC) based on ${H}_{2}/{H}_{\mathrm{\infty}}$ approach, and both of which are better than the passive suspension control. The proposed control methods are robust to the actuator faults and model uncertainties. The above simulation analysis show: whether the active suspension system is in good condition or malfunction in actuators and model uncertainties, both the integral sliding mode passive fault tolerant control and the robust passive fault tolerant control can improve the ride comfort of the suspension system to a certain extent.
6. Conclusions
In this study, the partial fault of actuators, timedomain hard constraints and model uncertainties of the suspension system are considered. A robust passive faulttolerant control (RPFTC) strategy and an integral sliding mode passive fault tolerant control (ISMPFTC) strategy are investigated; two passive faulttolerant control strategies based on ${H}_{2}/{H}_{\infty}$ approach have been applied to an active suspension system respectively. Road interference inputs to use filter white noise and bump response respectively. As to response of excitation of random road surface, in simulation, consider three cases. Concerning bump response, in simulation, consider three cases too, but in each case, consider three different vehicle speeds, which are $v=$20 km/h, $v=$25 km/h, $v=$30 km/h. Finally, an analysis of the simulation results is given to verify the feasibility and effectiveness of the proposed two control strategies is the main contributions of this work. The research we have done suggests that the two passive faulttolerant control strategies are robust to the actuator faults and model uncertainties, and can guarantee the stability of the vehicle active suspension system, improve the ride comfort of the vehicle simultaneously to a certain degree.
Acknowledgements
This work was supported by the Excellent Talents Project for the Second Level in the Education Department, Liaoning Province, China (No. LJQ2014065); Soft Science Research Plan Project, Science and Technology Department, Liaoning Province, China (No. JP2016017).
References
 Chen W. W., Wang Q. D., Xiao H. S., Zhang L. F. Integrated Vehicle Dynamics and Control. Wiley, 2016. [Publisher]
 Isermann R. Mechatronic Systems: Fundamentals. SpringerVerlag, 2005. [Search CrossRef]
 Tseng H. E., Hrovat D. State of the art survey: active and semiactive suspension control. Vehicle System Dynamics, Vol. 53, Issue 7, 2015, p. 10341062. [Publisher]
 Gillespie D T. Fundamentals of Vehicle Dynamics. Society of Automotive Engineers, 1992. [Publisher]
 Rajamani R. Vehicle Dynamics and Control. Springer Science and Business Media, 2011. [Search CrossRef]
 Cao D. P., Song X. B., Ahmadian M. Editors’ perspectives: road vehicle suspension design, dynamics, and control. Vehicle System Dynamics, Vol. 49, Issues 12, 2011, p. 328. [Publisher]
 Liu H. H., Gao H., Li P. Handbook of Vehicle Suspension Control Systems. United Kingdom, 2013. [Search CrossRef]
 Chen H., Guo K. An LMI approach to multiobjective RMS gain for active suspensions. Proceedings of the American Control Conference, Vol. 4, 2001, p. 26462651. [Publisher]
 Chen H., Guo K. Constrained H∞ control of active suspensions: an LMI approach. IEEE Transactions on Control Systems Technology, Vol. 13, Issue 3, 2005, p. 412421. [Publisher]
 Chen G. D., Yang Yu M. Y. L. Mixed H2/H∞ optimal guaranteed cost control of uncertain linear systems. Journal of Systems Science and Information, Vol. 2, Issue 3, 2004, p. 409416. [Search CrossRef]
 Guo L. X., Zhang L. P. Robust H∞ control of active vehicle suspension under nonstationary running. Journal of Sound and Vibration, Vol. 331, Issue 26, 2012, p. 58245837. [Publisher]
 Soliman H. M., Bajabaa N. S. Robust guaranteedcost control with regional pole placement of active suspensions. Journal of Vibration and Control, Vol. 19, Issue 8, 2013, p. 11701186. [Publisher]
 Bharalil J., Buragohain M. Design and performance analysis of fuzzy LQR; fuzzy PID and LQR controller for active suspension system using 3 degree of freedom quarter car model. IEEE International Conference on Power Electronics, Intelligent Control and Energy Systems, Delhi, India, 2016. [Search CrossRef]
 Bououden S., Chadli M., Zhang L. X., Yang T. Constrained model predictive control for time varying delay systems: application to an active car suspension. International Journal of Control, Automation, and Systems, Vol. 14, Issue 1, 2016, p. 5158. [Publisher]
 Blanke M., Kinnaert M., Lunze D. I. J. Introduction to diagnosis and faulttolerant control. Diagnosis and FaultTolerant Control, Vol. 49, Issue 6, 2003, p. 132. [Search CrossRef]
 Alwi H., Edwards C., Tan C. P. Fault Detection and FaultTolerant Control Using Sliding Modes. Springer London, 2011. [Publisher]
 Patton R. J. Faulttolerant control systems: the 1997 situation. IFAC Symposium on Fault Detection Supervision and Safety for Technical Processes, 1997. [Search CrossRef]
 Zhang Y., Jiang J. Bibliographical review on reconfigurable faulttolerant control systems. Annual Reviews in Control, Vol. 32, Issue 2, 2008, p. 229252. [Publisher]
 Benosman M. Passive Fault Tolerant Control. INTECH Open Access Publisher, 2011. [Publisher]
 Yang X. Z., Hong G. Robust adaptive faulttolerant compensation control with actuator failures and bounded disturbances. Acta Automatica Sinica, Vol. 35, Issue 3, 2009, p. 305309. [Search CrossRef]
 Gholami M. Passive fault tolerant control of piecewise affine systems based on H infinity synthesis. IFAC Proceedings, Vol. 44, Issue 1, 2011, p. 30843089. [Publisher]
 Jiang J. Faulttolerant Control SystemsAn Introductory Overview. Acta Automatica Sinica, Vol. 31, Issue 1, 2005, p. 161174. [Search CrossRef]
 Li H., Gao H., Liu H., Li M. Faulttolerant H∞ control for active suspension vehicle systems with actuator faults. Proceedings of the Institution of Mechanical Engineers, Part I: Journal of Systems and Control Engineering, Vol. 226, Issue 3, 2012, p. 348363. [Search CrossRef]
 Sun W. C., Pan H. H., Yu J. Y., Gao H. J. Reliability control for uncertain halfcar active suspension systems with possible actuator faults. IET Control Theory and Applications, Vol. 8, Issue 9, 2014, p. 746754. [Publisher]
 Wang R., Jing H., Karimi H. R., Chen N. Robust faulttolerant H∞ control of active suspension systems with finitefrequency constraint. Mechanical Systems and Signal Processing, Vol. 62, 2015, p. 341355. [Publisher]
 Liu B., Saif M., Fan H. Adaptive fault tolerant control of a halfcar active suspension systems subject to random actuator failures. IEEE/ASME Transactions on Mechatronics, Vol. 21, Issue 6, 2016, p. 28472857. [Publisher]
 Hamayun M. T., Edwards C., Alwi H. Fault Tolerant Control Schemes Using Integral Sliding Modes. Springer International Publishing, 2016. [Search CrossRef]
 Sam Y. M., Osman J. H., Ghani M. R. A. A class of proportionalintegral sliding mode control with application to active suspension system. Systems and Control Letters, Vol. 51, Issue 3, 2004, p. 217223. [Publisher]
 Chamseddine A., Noura H., Ouladsine M. Sensor faulttolerant control for active suspension using sliding mode techniques. Workshop on Networked Control Systems and FaultTolerant Control, 2005. [Search CrossRef]
 Dong Yu Guan X. M. Z. Adaptive sliding mode faulttolerant control for semiactive suspension using magnetorheological dampers. Journal of Intelligent Material Systems and Structures, Vol. 22, Issue 15, 2011, p. 16531660. [Publisher]
 Moradi M., Fekih A. Adaptive PIDslidingmode faulttolerant control approach for vehicle suspension systems subject to actuator faults. IEEE Transactions on Vehicular Technology, Vol. 63, Issue 3, 2014, p. 10411054. [Publisher]
 Moradi M., Fekih A. A stability guaranteed robust fault tolerant control design for vehicle suspension systems subject to actuator faults and disturbances. IEEE Transactions on Control Systems Technology, Vol. 23, Issue 3, 2015, p. 11641171. [Publisher]
Cited By
Energy
Junjiang Zhang, Yang Yang, Minghui Hu, Zhong Yang, Chunyun Fu

2021

Yun Zhang, Ming Yu, Bing Wang, Chenyu Xiao 
2020

ISA Transactions
Mahmoud A. Mossa, Hamdi Echeikh

2020
